TLP ThinkPad T60 2008 43 G - Versionsgeschichte

Revealed am 5. November 2015 um 12:12 Uhr

2015-11-05T12:12:48Z

Revealed: /* IBM/Lenovo */ Config aktualisiert

2015-10-23T10:11:19Z

‎IBM/Lenovo: Config aktualisiert

Revealed am 15. August 2015 um 11:51 Uhr

2015-08-15T11:51:24Z

Revealed am 15. August 2015 um 11:31 Uhr

2015-08-15T11:31:25Z

Revealed am 15. August 2015 um 11:25 Uhr

2015-08-15T11:25:57Z

Revealed am 14. August 2015 um 18:44 Uhr

2015-08-14T18:44:13Z

Revealed am 14. August 2015 um 12:48 Uhr

2015-08-14T12:48:14Z

Revealed: Die Seite wurde neu angelegt: „# ------------------------------------------------------------------------------ # tlp - Parameters for power save # Hint: some features are disabled by defau…“

2015-08-14T12:46:40Z

Die Seite wurde neu angelegt: „# ------------------------------------------------------------------------------ # tlp - Parameters for power save # Hint: some features are disabled by defau…“

Neue Seite

# ------------------------------------------------------------------------------
# tlp - Parameters for power save

# Hint: some features are disabled by default, remove the leading # to enable
# them.

# Set to 0 to disable, 1 to enable TLP.
TLP_ENABLE=1

# Seconds laptop mode has to wait after the disk goes idle before doing a sync.
# Non-zero value enables, zero disables laptop mode.
DISK_IDLE_SECS_ON_AC=2
DISK_IDLE_SECS_ON_BAT=2

# Dirty page values (timeouts in secs).
MAX_LOST_WORK_SECS_ON_AC=15
MAX_LOST_WORK_SECS_ON_BAT=60

# Hint: CPU parameters below are disabled by default, remove the leading #
# to enable them, otherwise kernel default values are used.

# Select a CPU frequency scaling governor:
# ondemand, powersave, performance, conservative
# Intel Core i processor with intel_pstate driver:
# powersave, performance
# Important:
# You *must* disable your distribution's governor settings or conflicts will
# occur. ondemand is sufficient for *almost all* workloads, you should know
# what you're doing!
CPU_SCALING_GOVERNOR_ON_AC=ondemand
CPU_SCALING_GOVERNOR_ON_BAT=ondemand

# Set the min/max frequency available for the scaling governor.
# Possible values strongly depend on your CPU. For available frequencies see
# tlp-stat output, Section "+++ Processor".
#CPU_SCALING_MIN_FREQ_ON_AC=0
#CPU_SCALING_MAX_FREQ_ON_AC=0
#CPU_SCALING_MIN_FREQ_ON_BAT=0
#CPU_SCALING_MAX_FREQ_ON_BAT=0

# Set Intel P-state performance: 0..100 (%)
# Limit the max/min P-state to control the power dissipation of the CPU.
# Values are stated as a percentage of the available performance.
# Requires an Intel Core i processor with intel_pstate driver.
#CPU_MIN_PERF_ON_AC=0
#CPU_MAX_PERF_ON_AC=100
#CPU_MIN_PERF_ON_BAT=0
#CPU_MAX_PERF_ON_BAT=30

# Set the CPU "turbo boost" feature: 0=disable, 1=allow
# Requires an Intel Core i processor.
# Important:
# - This may conflict with your distribution's governor settings
# - A value of 1 does *not* activate boosting, it just allows it
#CPU_BOOST_ON_AC=1
#CPU_BOOST_ON_BAT=0

# Minimize number of used CPU cores/hyper-threads under light load conditions
SCHED_POWERSAVE_ON_AC=1
SCHED_POWERSAVE_ON_BAT=1

# Kernel NMI Watchdog:
# 0=disable (default, saves power), 1=enable (for kernel debugging only)
NMI_WATCHDOG=0

# Change CPU voltages aka "undervolting" - Kernel with PHC patch required
# Frequency voltage pairs are written to:
# /sys/devices/system/cpu/cpu0/cpufreq/phc_controls
# CAUTION: only use this, if you thoroughly understand what you are doing!
#PHC_CONTROLS="F:V F:V F:V F:V"

# Set CPU performance versus energy savings policy:
# performance, normal, powersave
# Requires kernel module msr and x86_energy_perf_policy from linux-tools
ENERGY_PERF_POLICY_ON_AC=performance
ENERGY_PERF_POLICY_ON_BAT=powersave

# Hard disk devices; separate multiple devices with spaces (default: sda).
# Devices can be specified by disk ID also (lookup with: tlp diskid).
DISK_DEVICES="sda sdb"

# Hard disk advanced power management level: 1..254, 255 (max saving, min, off)
# Levels 1..127 may spin down the disk; 255 allowable on most drives.
# Separate values for multiple devices with spaces.
DISK_APM_LEVEL_ON_AC="192 192"
DISK_APM_LEVEL_ON_BAT="172 172"

# Hard disk spin down timeout:
# 0: spin down disabled
# 1..240: timeouts from 5s to 20min (in units of 5s)
# 241..251: timeouts from 30min to 5.5 hours (in units of 30min)
# See 'man hdparm' for details.
DISK_SPINDOWN_TIMEOUT_ON_AC="0 12"
DISK_SPINDOWN_TIMEOUT_ON_BAT="0 12"

# Select IO scheduler for the disk devices: noop, deadline, cfq (Default: cfq);
# Separate values for multiple devices with spaces.
#DISK_IOSCHED="cfq cfq"

# SATA aggressive link power management (ALPM):
# min_power, medium_power, max_performance
SATA_LINKPWR_ON_AC=medium_power
SATA_LINKPWR_ON_BAT=medium_power

# PCI Express Active State Power Management (PCIe ASPM):
# default, performance, powersave
PCIE_ASPM_ON_AC=powersave
PCIE_ASPM_ON_BAT=powersave

# Radeon graphics clock speed (profile method): low, mid, high, auto, default;
# auto = mid on BAT, high on AC; default = use hardware defaults.
# (Kernel >= 2.6.35 only, open-source radeon driver explicitly)
RADEON_POWER_PROFILE_ON_AC=mid
RADEON_POWER_PROFILE_ON_BAT=low

# Radeon dynamic power management method (DPM): battery, performance
# (Kernel >= 3.11 only, requires boot option radeon.dpm=1)
RADEON_DPM_STATE_ON_AC=battery
RADEON_DPM_STATE_ON_BAT=battery

# Radeon DPM performance level: auto, low, high; auto is recommended.
RADEON_DPM_PERF_LEVEL_ON_AC=auto
RADEON_DPM_PERF_LEVEL_ON_BAT=auto

# WiFi power saving mode: 1=disable, 5=enable; not supported by all adapters.
WIFI_PWR_ON_AC=5
WIFI_PWR_ON_BAT=5

# Disable wake on LAN: Y/N
WOL_DISABLE=Y

# Enable audio power saving for Intel HDA, AC97 devices (timeout in secs).
# A value of 0 disables, >=1 enables power save.
SOUND_POWER_SAVE_ON_AC=1
SOUND_POWER_SAVE_ON_BAT=1

# Disable controller too (HDA only): Y/N
SOUND_POWER_SAVE_CONTROLLER=Y

# Set to 1 to power off optical drive in UltraBay/MediaBay when running on
# battery. A value of 0 disables this feature (Default).
# Drive can be powered on again by releasing (and reinserting) the eject lever
# or by pressing the disc eject button on newer models.
# Note: an UltraBay/MediaBay hard disk is never powered off.
BAY_POWEROFF_ON_BAT=0
# Optical drive device to power off (default sr0).
BAY_DEVICE="sr0"

# Runtime Power Management for PCI(e) bus devices: on=disable, auto=enable
RUNTIME_PM_ON_AC=auto
RUNTIME_PM_ON_BAT=auto

# Runtime PM for *all* PCI(e) bus devices, except blacklisted ones:
# 0=disable, 1=enable
RUNTIME_PM_ALL=1

# Exclude PCI(e) device adresses the following list from Runtime PM
# (separate with spaces). Use lspci to get the adresses (1st column).
#RUNTIME_PM_BLACKLIST="bb:dd.f 11:22.3 44:55.6"

# Exclude PCI(e) devices assigned to the listed drivers from Runtime PM
# (should prevent accidential power on of hybrid graphics' discrete part).
# Default is "radeon nouveau"; use "" to disable the feature completely.
# Separate multiple drivers with spaces.
RUNTIME_PM_DRIVER_BLACKLIST="radeon nouveau"

# Set to 0 to disable, 1 to enable USB autosuspend feature.
USB_AUTOSUSPEND=1

# Exclude listed devices from USB autosuspend (separate with spaces).
# Use lsusb to get the ids.
# Note: input devices (usbhid) are excluded automatically (see below)
#USB_BLACKLIST="1111:2222 3333:4444"

# Exclude devices assigned to the listed drivers from USB autosuspend.
# Default is "usbhid" (input devices); use "" to disable the feature
# completely. Separate multiple drivers with spaces.
USB_DRIVER_BLACKLIST="usbhid"

# WWAN devices are excluded from USB autosuspend:
# 0=do not exclude / 1=exclude
USB_BLACKLIST_WWAN=1

# Include listed devices into USB autosuspend even if already excluded
# by the driver or WWAN blacklists above (separate with spaces).
# Use lsusb to get the ids.
#USB_WHITELIST="1111:2222 3333:4444"

# Set to 1 to disable autosuspend before shutdown, 0 to do nothing
# (workaround for USB devices that cause shutdown problems).
#USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN=1

# Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown
# on system startup: 0=disable, 1=enable.
# Hint: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below
# are ignored when this is enabled!
RESTORE_DEVICE_STATE_ON_STARTUP=0

# Radio devices to disable on startup: bluetooth, wifi, wwan.
# Separate multiple devices with spaces.
DEVICES_TO_DISABLE_ON_STARTUP="bluetooth wwan"

# Radio devices to enable on startup: bluetooth, wifi, wwan.
# Separate multiple devices with spaces.
#DEVICES_TO_ENABLE_ON_STARTUP="wifi"

# Radio devices to disable on shutdown: bluetooth, wifi, wwan
# (workaround for devices that are blocking shutdown).
#DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan"

# Radio devices to enable on shutdown: bluetooth, wifi, wwan
# (to prevent other operating systems from missing radios).
#DEVICES_TO_ENABLE_ON_SHUTDOWN="wwan"

# Radio devices to enable on AC: bluetooth, wifi, wwan
#DEVICES_TO_ENABLE_ON_AC="bluetooth wifi wwan"

# Radio devices to disable on battery: bluetooth, wifi, wwan
#DEVICES_TO_DISABLE_ON_BAT="bluetooth wifi wwan"

# Radio devices to disable on battery when not in use (not connected):
# bluetooth, wifi, wwan
#DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan"

# Battery charge thresholds (ThinkPad only, tp-smapi or acpi-call kernel module
# required). Charging starts when the remaining capacity falls below the
# START_CHARGE_TRESH value and stops when exceeding the STOP_CHARGE_TRESH value.
# Main / Internal battery (values in %)
#START_CHARGE_THRESH_BAT0=75
#STOP_CHARGE_THRESH_BAT0=80
# Ultrabay / Slice / Replaceable battery (values in %)
#START_CHARGE_THRESH_BAT1=75
#STOP_CHARGE_THRESH_BAT1=80

# ------------------------------------------------------------------------------
# tlp-rdw - Parameters for the radio device wizard
# Possible devices: bluetooth, wifi, wwan

# Hints:
# - Parameters are disabled by default, remove the leading # to enable them.
# - Separate multiple radio devices with spaces.

# Radio devices to disable on connect.
DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan"
DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan"
DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi"

# Radio devices to enable on disconnect.
DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan"
#DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT=""
#DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT=""

# Radio devices to enable/disable when docked.
#DEVICES_TO_ENABLE_ON_DOCK=""
#DEVICES_TO_DISABLE_ON_DOCK=""

# Radio devices to enable/disable when undocked.
#DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
#DEVICES_TO_DISABLE_ON_UNDOCK=""

@@ Zeile 75: / Zeile 75: @@
 #   performance, normal, powersave
 # Requires kernel module msr and x86_energy_perf_policy from linux-tools
-ENERGY_PERF_POLICY_ON_AC=performance
+ENERGY_PERF_POLICY_ON_AC=powersave
 ENERGY_PERF_POLICY_ON_BAT=powersave

@@ Zeile 10: / Zeile 10: @@
 # Seconds laptop mode has to wait after the disk goes idle before doing a sync.
 # Non-zero value enables, zero disables laptop mode.
-DISK_IDLE_SECS_ON_AC=2
+DISK_IDLE_SECS_ON_AC=0
-DISK_IDLE_SECS_ON_BAT=2
+DISK_IDLE_SECS_ON_BAT=510
-# Dirty page values (timeouts in secs).
+# Dirty page values (timeouts in secs). # 15 # 60
-MAX_LOST_WORK_SECS_ON_AC=15
+#MAX_LOST_WORK_SECS_ON_AC=15
-MAX_LOST_WORK_SECS_ON_BAT=60
+#MAX_LOST_WORK_SECS_ON_BAT=60
 # Hint: CPU parameters below are disabled by default, remove the leading #
@@ Zeile 82: / Zeile 84: @@
 # Hard disk advanced power management level: 1..254, 255 (max saving, min, off)
 # Levels 1..127 may spin down the disk; 255 allowable on most drives.
-# Separate values for multiple devices with spaces.
+# Separate values for multiple devices with spaces. # 127
 DISK_APM_LEVEL_ON_AC="192 192"
-DISK_APM_LEVEL_ON_BAT="172 172"
+DISK_APM_LEVEL_ON_BAT="64 64"
 # Hard disk spin down timeout:
-#   0:        spin down disablede
+#   0:        spin down disabled --- 12 x 5s = 1 Min.
 #   1..240:   timeouts from 5s to 20min (in units of 5s)
 #   241..251: timeouts from 30min to 5.5 hours (in units of 30min)
-# See 'man hdparm' for details.
+# See 'man hdparm' for details. ### 24
-DISK_SPINDOWN_TIMEOUT_ON_AC="0 12"
+DISK_SPINDOWN_TIMEOUT_ON_AC="24 24"
-DISK_SPINDOWN_TIMEOUT_ON_BAT="0 12"
+DISK_SPINDOWN_TIMEOUT_ON_BAT="8 8"
 # Select IO scheduler for the disk devices: noop, deadline, cfq (Default: cfq);
@@ Zeile 101: / Zeile 103: @@
 #   min_power, medium_power, max_performance
 SATA_LINKPWR_ON_AC=medium_power
-SATA_LINKPWR_ON_BAT=medium_power
+SATA_LINKPWR_ON_BAT=min_power
 # PCI Express Active State Power Management (PCIe ASPM):
@@ Zeile 207: / Zeile 209: @@
 # Radio devices to disable on shutdown: bluetooth, wifi, wwan
 # (workaround for devices that are blocking shutdown).
-DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan"
+DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wwan"
 # Radio devices to enable on shutdown: bluetooth, wifi, wwan
@@ Zeile 217: / Zeile 219: @@
 # Radio devices to disable on battery: bluetooth, wifi, wwan
-#DEVICES_TO_DISABLE_ON_BAT="bluetooth wifi wwan"
+#DEVICES_TO_DISABLE_ON_BAT="bluetooth wwan"
 # Radio devices to disable on battery when not in use (not connected):
 # bluetooth, wifi, wwan
-DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan"
+DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wwan"
 # Battery charge thresholds (ThinkPad only, tp-smapi or acpi-call kernel module
@@ Zeile 247: / Zeile 249: @@
 # Radio devices to enable on disconnect.
-DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan"
+DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi"
 #DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT=""
-#DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT=""
+#DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT="wifi"
 # Radio devices to enable/disable when docked.
@@ Zeile 256: / Zeile 258: @@
 # Radio devices to enable/disable when undocked.
-#DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
+DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
 #DEVICES_TO_DISABLE_ON_UNDOCK=""
 </pre>

@@ Zeile 87: / Zeile 87: @@
 # Hard disk spin down timeout:
-#   0:        spin down disabled
+#   0:        spin down disablede
 #   1..240:   timeouts from 5s to 20min (in units of 5s)
 #   241..251: timeouts from 30min to 5.5 hours (in units of 30min)
@@ Zeile 143: / Zeile 143: @@
 # or by pressing the disc eject button on newer models.
 # Note: an UltraBay/MediaBay hard disk is never powered off.
-BAY_POWEROFF_ON_BAT=0
+BAY_POWEROFF_ON_BAT=1
 # Optical drive device to power off (default sr0).
 BAY_DEVICE="sr0"
@@ Zeile 195: / Zeile 195: @@
 # Hint: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below
 #   are ignored when this is enabled!
-RESTORE_DEVICE_STATE_ON_STARTUP=1
+RESTORE_DEVICE_STATE_ON_STARTUP=0
 # Radio devices to disable on startup: bluetooth, wifi, wwan.
@@ Zeile 203: / Zeile 203: @@
 # Radio devices to enable on startup: bluetooth, wifi, wwan.
 # Separate multiple devices with spaces.
-#DEVICES_TO_ENABLE_ON_STARTUP="wifi"
+DEVICES_TO_ENABLE_ON_STARTUP="wifi"
 # Radio devices to disable on shutdown: bluetooth, wifi, wwan
 # (workaround for devices that are blocking shutdown).
-#DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan"
+DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan"
 # Radio devices to enable on shutdown: bluetooth, wifi, wwan
@@ Zeile 214: / Zeile 214: @@
 # Radio devices to enable on AC: bluetooth, wifi, wwan
-#DEVICES_TO_ENABLE_ON_AC="bluetooth wifi wwan"
+DEVICES_TO_ENABLE_ON_AC="bluetooth wifi wwan"
 # Radio devices to disable on battery: bluetooth, wifi, wwan
@@ Zeile 221: / Zeile 221: @@
 # Radio devices to disable on battery when not in use (not connected):
 # bluetooth, wifi, wwan
-#DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan"
+DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan"
 # Battery charge thresholds (ThinkPad only, tp-smapi or acpi-call kernel module

@@ Zeile 112: / Zeile 112: @@
 # (Kernel >= 2.6.35 only, open-source radeon driver explicitly)
 RADEON_POWER_PROFILE_ON_AC=mid
-RADEON_POWER_PROFILE_ON_BAT=low
+RADEON_POWER_PROFILE_ON_BAT=mid
 # Radeon dynamic power management method (DPM): battery, performance

@@ Zeile 1: / Zeile 1: @@
-# ------------------------------------------------------------------------------
+<pre># ------------------------------------------------------------------------------
 # tlp - Parameters for power save
@@ Zeile 258: / Zeile 258: @@
 #DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
 #DEVICES_TO_DISABLE_ON_UNDOCK=""